To drill a hole in the wall can be a difficult task. You must know the proper techniques to drill holes in different types of the wall surface. You can also check some best drill machines to buy from amazon. Walls can be made up of different materials. Such as it can be made of wood or it can be made of glass or it can be a concrete wall or it can be plasterboard. You must know to choose the proper drilling tool for different types of walls. this is done on the basis of the work which is carried out as a whole and the right intent for which it is worked through. Making a hole in the wall can be really worked out but then if you have a worked up management then it can be good enough for you to know the details.
In case of a wooden wall:
If you have to drill a hole in a wooden wall, you have to use a spur point bit. This type of bit is also known as a wood bit. These bits have two raised spurs with a central section in the middle. The sharp pointed tip of the tool helps to keep the bit drill straight in the wood. This type of drilling tool is useful for drilling holes in hollow walls or any plastic material. Spur point bits work very quickly and the sides of the hole made by them are clean and parallel. The sharpening of the spur point is done by hand with the use of a grindstone or fine file.
In case of a glass wall:
If you have to drill a hole in a glass wall or a ceramic wall or a tile wall, you have to use a tile bit. This bit can penetrate the walls without damaging the wall material. The tips of the tile bit are of carbide and look like a spear. The spear-like tip helps the tool to cut through the hard materials. The sharpening of the tool is difficult due to the hard carbide curved cutting edge.
In case of a concrete wall:
If you have to drill a hole in a concrete or stone wall, you have to use a masonry drill bit. The tip of the bit is made of tungsten carbide that helps in cutting through hard materials, such as brick or stone walls. Most of the masonry bits are used with a hammer action to drill in the wall. While drilling a hole in the wall with masonry bits, slowly rotate the bit to avoid the overheating of the bit. This bit is sharpened with a drill sharpener.
In the case of plasterboard:
If you have to drill a hole in the plasterboard, you have to use a drywall bit. A drywall bit is used to drill holes in the smooth walls. If the wall sounds hollow, then these bits work best to drill holes. To hang anything with a drywall anchor it should be placed firmly by a screwdriver to maintain the strong grip.
Then it is the step to locate the positions on the wall to make the holes. You must know which are the preferable and safe positions to drill a hole in the wall.
Do not drill over or near electrical wires. To prevent any sort of harm and risk you must stay away from drilling in the places of switch outlets. You must be very careful while searching for the electric areas. Even a small careless activity would be dangerous for your life.
You can use wire detectors to find out the wires before you start to drill in the wall.
Mark the position you need to drill a hole in the wall. Before starting the bit to drill in the wall, mark the point with a pencil or removable marker so that it does not leave any mark after the work is complete.
If you have to make two holes in the same line parallel to each other, you can use a measuring scale or a tape to mark the positions of the properly spaced holes. You can make a cross sign or a dot over the wall to make out the exact position while drilling.
Drilling a hole in the wall by the drill bit has some methods and they are done with some safety measures. Such as –
The process of drilling produces a lot of dust. These specs of dust can be allergic to many people. To avoid inhaling this dust or to avoid any sort of irritation from this dust, you can wear a dust mask. Safety equipment for eyes, such as safety goggles, is also necessary to prevent the choking of dust particles in the eyes.
Checking the safety measures before starting drilling activity is essential.
The next step is to put the drilling tool in the exact position as marked earlier. Place the driller perpendicularly to the wall and start drilling. Slowly press the bit against the wall so that it enters the wall and makes a hole. Stop the drill when you reach the required position and size of the whole.
Then place the hook or an anchor inside the drill hole. The anchor must be placed firmly inside the hole so that it can securely hold the screw put inside it.
Once the processes are complete hang your selected items from the hook or fasten the items together with the screw.…